Home / Products / Engine Suite
Product — Quark Solutions Engine Suite

Validate the model. Prove the part.

Engine Suite is a modular platform for pre- and post-validation of manufacturing. It prepares a design model, runs your engineering rules against it, carries the results through simulation and inspection, and produces the evidence an engineer can sign their name to.

ModularRun one or all
Rule-drivenYour standards
TraceableEvery check recorded
Why it exists

Validation is usually a folder, not a system

In most engineering teams the checks exist — in a checklist, a spreadsheet, a macro someone wrote years ago, and in the heads of two senior engineers. The knowledge is real. It just is not repeatable, and it does not travel with the model.

Engine Suite makes the same checks executable. The rules become configuration, the run becomes a record, and the outcome becomes a document — with the 3D evidence attached to it.

Before release

Geometry health, manufacturability and standards compliance, checked automatically on every revision instead of at the end.

After manufacture

Measured and scanned data compared against nominal, with deviation reported in the same language as the design intent.

Inside the suite

Six modules, one data model

Each module is useful on its own and stronger in sequence. Everything they produce writes back to a single project record, so nothing is stranded in a file on someone's desktop.

/ 01

Engine Prep

Import from native and neutral formats, heal broken geometry, normalise units and structure, and build the clean model everything downstream depends on.

  • Import & translation
  • Geometry healing
  • Simplification & defeaturing
/ 02

Engine Check

Your engineering standards expressed as executable rules, run over a part or a whole assembly with findings pinned to the geometry that caused them.

  • Design-rule & DFM checks
  • Configurable rule sets
  • Severity and waiver handling
/ 03

Engine Solve

Hand-off to your simulation stack — model preparation, batch runs and parametric studies driven from the same project, without re-keying inputs.

  • Meshing workflow support
  • Batch & parametric runs
  • Solver-agnostic interfaces
/ 04

Engine View

A fast 3D review environment for large assemblies, with measurement, sectioning, comparison and markup that non-CAD stakeholders can use.

  • Large-assembly performance
  • Measure, section, explode
  • Revision comparison
/ 05

Engine Report

Documents generated from the run itself — findings, 3D snapshots, measured values and approvals — in the template your customer or auditor expects.

  • Templated PDF / DOCX output
  • 3D evidence embedded
  • Approval & sign-off trail
/ 06

Engine Link

The connective tissue: CAD and PLM hooks, shop-floor and inspection data in, and APIs so the suite fits the toolchain you already run.

  • CAD / PLM integration
  • Inspection & CMM data import
  • REST API and scripting
How a run works

From model to signed report

A typical Engine Suite cycle, whether triggered by an engineer or by a release event in your PLM.

Every step is recorded. Model revision, rule set version, who ran it and what was waived — so a result from six months ago can still be explained.

Ingest

The model arrives from CAD, PLM or a watched folder and is prepared automatically.

Check

The applicable rule set runs; findings are classified by severity and attached to geometry.

Review

Engineers examine findings in 3D, accept, waive with reason, or send back for change.

Correlate

Simulation results and, later, measured data are compared against the same intent.

Report

Evidence is compiled, approved and released to whoever needs it — internal or customer.

Fit & deployment

Designed to fit an existing toolchain

Engine Suite is not a replacement for your CAD, PLM or solver. It sits between them and does the part none of them do well: making engineering judgement repeatable.

Deployment, integrations and rule sets are configured per customer during onboarding — the suite ships with a working baseline and is tuned to your standards from there.

  • Model inputNeutral formats (STEP, IGES, JT, Parasolid, STL) and native CAD via the appropriate exchange toolkit.
  • Assembly scaleBuilt for production assemblies, not sample parts — tessellation and memory strategy tuned for size.
  • RulesConfigurable rule sets per product line, discipline or customer standard; versioned alongside the project.
  • IntegrationCAD add-ins, PLM hooks, REST API, scripting and watched-folder automation.
  • Inspection dataCMM and scan results imported for nominal-versus-actual comparison.
  • OutputTemplated reports, 3D snapshots, structured result data for downstream analytics.
  • DeploymentOn-premise or private cloud; edge-friendly for plant-side use.
  • LicensingPer-seat or per-site, module by module. Talk to us about a pilot.
What changes

What teams get out of it

Fewer late surprises

Problems found at the model stage instead of on the shop floor, where they cost tooling time and rework.

Knowledge that stays

Senior engineers' judgement captured as rules the whole team runs — and that survives people changing roles.

Audit-ready evidence

Reports generated from actual runs, with traceability back to the exact revision and rule set used.

Consistent standards

The same checks applied across sites, suppliers and product lines, regardless of who prepared the model.

Faster review cycles

Reviewers see findings in 3D with context, instead of reconstructing the issue from a screenshot in an email.

A path to automation

Once checks are executable, they can run on every release — unattended, on your infrastructure.

See Engine Suite on your own model

The fastest way to judge it is to run it against a part you already argue about. Send us a representative model and the checks you care about, and we will walk you through the result.